WUN 90

Μεταβατική ηλεκτρογωνία 90° HD-PE/Brass

Compact transition fitting. HD-PE end with exposed heating coils for optimal heat transfer, large insertion depth, wide fusion zone plus cold zones at the end and in the transition area to prevent the flow of molten material for use without holding devices. Brass end permanently anchored in the HD-PE. Cannot be released or rotated. Self sealing patented sealing geometry without elastomer seal. For use in water systems.

Standard: Brass. Gunmetal on request.

Other thread sizes on request

Compact transition fitting. HD-PE end with exposed heating coils for optimal heat transfer, large insertion depth, wide fusion zone plus cold zones at the end and in the transition area to prevent the flow of molten material for use without holding devices. Brass end permanently anchored in the HD-PE. Cannot be released or rotated. Self sealing patented sealing geometry without elastomer seal. For use in water systems.

Standard: Brass. Gunmetal on request.

Other thread sizes on request

Επιστροφή Τεχνικό Φυλλάδιο

PE 100 SDR 11

Maximum working pressure 16 bar (water)

Κωδικός προϊόντος d BX PU D R L t z1 z2 h Weight kg
612120 32 20 1000 47 1" 85 42 21 89 24 0,350
612140 32 20 800 47 1 1/2" 94 42 21 93 24 0,480
612127 40 15 750 58 1" 102 46 27 101 30 0,520
612122 40 15 750 58 1 1/4" 102 46 27 103 30 0,530
612121 40 15 750 58 1 1/2" 102 46 27 104 30 0,560
612119 50 10 500 70 1" 118 53 30 110 30 0,680
612123 50 10 500 70 1 1/4" 118 53 30 112 30 0,660
612124 50 10 500 70 1 1/2" 118 53 30 113 30 0,680
612125 63 10 320 84 1 1/2" 128 53 33 116 35 0,990
612126 63 10 320 84 2" 128 53 33 121 35 1,030

Other thread sizes on request

FRIALEN safety fittings can be fused to pipes SDR11 - SDR 17.6. Minimum wall thickness s min ≥ 3 mm. Other SDR-stages on request. Please observe the marking directly at the product, which is mandatory. DVGW-Registration No. DV-7501AU2256

Standard: Brass. Gunmetal and V2A on request

Areas of Application

FRIALEN-Transition Elbows WUN 90° are threaded joints as an adaptor from a metal pipe with internal thread to a HD-PE pipe. Joint on the part of HD-PE by FRIALEN-Coupler.

Assembly Instructions

The threaded component must be held with a spanner to prevent it twisting in the HD-PE component. The fusion of the HD-PE side takes place by FRIALEN-fusing – leakproof and longitudinally strong.

The installation of the brass and the HD-PE side has to be prepared according to the general installation instructions (see ”Transition Fittings with threaded connection” in ”Assembly Instructions” for ”FRIALEN-Safety Fittings for house connections and distribution pipes up to d 225”). This involves removing the oxide skin and cleaning the pipe ends.

Good reasons for using the FRIALEN-Transition Elbows WUN 90°:

Compact construction

HD-PE side with exposed heating element for optimal heat transfer

Cold zones at the end to prevent the flow of molten material

No holding clamps required

Large insertion depth, extra wide fusion zones

Brass end permanently anchored in the HD-PE and will not distort

Self sealing patented sealing geometry without elastomer seal

Additional barcode for tracing back the underground fitting (Traceability-Coding)